Camera Battery Runtime Calculator — Capacity, Power Draw & Recording Time
Estimate how long a camera or complete cinema rig can run from batteries rated in watt-hours or mAh. Apply a realistic usable-capacity allowance and check coverage of a target powered time. Multiple sequential batteries provide cumulative powered time; battery changes may interrupt recording.
Battery and camera rig
Estimated powered runtime
Usable recording-power estimate2 hr 31 min2:31:12 total (2.52 hours)
Rated energy98 Wh
Usable energy88.2 Wh
Runtime per battery2 hr 31 min
Energy per recording hour35 Wh
Target coverage
One battery covers about 63% of the 4-hour target. Plan for 2 equal batteries.
The target requires about 155.56 Wh of rated capacity at a 90% usable-capacity assumption.
How to estimate camera battery runtime
Use watt-hours when the label provides them. Wh already combines electrical capacity and nominal voltage, so it is the clearest value for comparing different battery systems.
Otherwise enter mAh and nominal voltage. Do not use the fully charged voltage. The calculator converts the battery rating to Wh.
Enter the complete rig's average draw. Include any monitor, external recorder, wireless transmitter, lens motor, follow focus, adapter, or other accessory powered from the same pack. Device-side consumption excludes losses in the power conversion between the battery and those devices. Average power measured at the battery output includes downstream conversion losses; do not deduct those same losses again through the usable-capacity allowance. Record where the draw was measured.
Choose a usable-capacity percentage. The default 90% is only a planning assumption. Replace it with a measured value for the tested configuration or an appropriate planning allowance. Match the allowance to the measurement point: account for conversion losses when using device-side consumption, but do not deduct losses already included in a battery-output measurement. Identify any additional production reserve separately.
Add a target time if useful. The result shows target coverage and the total whole number of equal batteries required, not the number of additional batteries to obtain. Subtract the suitable, fully charged equal batteries already available from that total, with a minimum of zero additional batteries. Sequential batteries provide cumulative powered time and may require recording interruptions during changes.
Test the actual configuration. Use this checklist for a representative test: record the battery's rated Wh, starting charge and condition; recording mode and display settings; accessories sharing the battery; temperature; average draw and its measurement point; and observed powered runtime. Estimate the usable-capacity fraction as average draw in W × observed runtime in hours ÷ rated Wh. This estimate applies to the tested configuration and measurement point. Identify any additional production reserve separately rather than treating it as measured battery performance.
Camera battery capacity and runtime formulas
Battery energy in watt-hours combines charge capacity and nominal voltage. For a battery rated in milliamp-hours:
For n equal batteries and usable-capacity fraction u:
usable energy (Wh) = Wh per battery × n × u runtime (hours) = usable energy (Wh) ÷ average power (W)
When a target recording time is entered, the calculator reverses the relationship:
required rated capacity (Wh) = target hours × average power (W) ÷ u required batteries = round up(required capacity ÷ Wh per battery)
A watt-hour is energy delivered by one watt for one hour. At a steady 35 W, a rig consumes 35 Wh each hour. Actual camera draw is rarely perfectly steady, so the average must represent the intended shooting setup. In a hypothetical example with one 98 Wh battery, a 35 W average load, 90% usable capacity and a four-hour target, u = 0.90. Usable energy is 98 × 0.90 = 88.2 Wh, giving 88.2 ÷ 35 = 2.52 hours per battery. One battery covers 2.52 ÷ 4 × 100 = 63% of the target. Required rated capacity is 4 × 35 ÷ 0.90 ≈ 155.56 Wh. Dividing by 98 Wh gives about 1.59 batteries, which rounds up to two batteries in total. If one suitable, fully charged 98 Wh battery is already available, one additional equal battery is needed. Sequential use provides cumulative powered time; it does not guarantee uninterrupted recording during battery changes.
Resolution, frame rate, codec processing, and sensor mode can change camera load.
Measure or test in the exact recording mode.
Accessories
Monitors, recorders, wireless video, focus motors, and USB devices add to battery draw.
Add every device powered by the same battery.
Conversion and cutoff
Voltage regulators consume energy, and the battery or camera may shut down before every rated Wh is delivered.
Allow for cutoff and conversion losses not already included in the entered draw. Do not deduct downstream conversion losses again when average draw is measured at the battery output.
Battery condition
Age, cycle history, state of charge, high load, and cold temperatures can reduce delivered energy.
Use a conservative factor or measured discharge result.
Camera activity
Autofocus, stabilization, display brightness, playback, pre-record, and wireless functions vary over time.
Use average draw from a representative test, not only idle power.
Non-battery limits
Media capacity, overheating, clip limits, and operational pauses can end continuous recording first.
Plan those constraints separately from powered runtime.
Planning estimate, compatibility, and battery safety
This calculator estimates energy runtime; it does not validate electrical compatibility. Confirm voltage range, polarity, connector wiring, maximum continuous current, output-power rating, cable rating, battery-management limits, and the equipment manufacturer's instructions before connecting anything. Never improvise series or parallel battery wiring.
The result is not a guarantee of uninterrupted recording. Battery gauges and published capacities have tolerances, while real loads and conditions change. Keep a suitable reserve, use healthy batteries and approved chargers, and stop using any pack that is swollen, damaged, unusually hot, leaking, or recalled. For critical productions, perform a timed test and provide independent backup power.
Camera battery runtime FAQ
How do I calculate runtime from Wh and watts?
Divide usable watt-hours by average watts. A 98 Wh battery at 90% usable capacity provides 88.2 Wh; at an average 35 W, the estimate is 2.52 hours, or about 2 hours 31 minutes.
How do I convert mAh to Wh?
Divide mAh by 1,000, then multiply by nominal voltage. A 6,800 mAh, 14.4 V battery is 6.8 Ah × 14.4 V = 97.92 Wh. The same mAh rating at a different voltage represents a different amount of energy.
Should I use camera power consumption or battery output watts?
Use the rig's average consumption or its average draw measured at the battery output, with a usable-capacity allowance matched to that measurement point. Device-side consumption needs an allowance for upstream conversion losses; a battery-output measurement already includes downstream conversion losses, so do not deduct them again. A battery's maximum output wattage is a compatibility limit, not the load it forces into the camera. The battery must still support the rig's peak and continuous draw.
What usable-capacity percentage should I enter?
Use your own measured result when possible, remembering that it applies to the tested configuration and measurement point. Otherwise choose a planning allowance that reflects battery health, temperature, load, cutoff, and conversion losses not already included in the entered draw. Identify any additional production reserve separately. The 90% default is an editable assumption, not a promise.
Can I multiply runtime by the number of batteries?
Yes, for cumulative powered time when equal, fully charged batteries are used sequentially under the same load and conditions. Battery changes may interrupt recording, and changeover time is not powered runtime. It also applies to a properly designed compatible bank whose rated energies can be combined. Entering multiple batteries does not guarantee hot swapping. Hot-swap behaviour and unequal batteries require system-specific guidance.
Does the estimate include a monitor and wireless transmitter?
Only if their average watts are included in the entered total rig draw. Accessories powered from separate batteries should not be counted against this battery pool.
Why can a camera stop recording before the calculated time?
The estimate covers electrical runtime only. A full card, thermal shutdown, file-duration limit, battery voltage cutoff, or other camera restriction can stop a recording earlier.
Does this calculator save my equipment details?
Choosing clipboard copy places results on your clipboard; choosing a CSV download saves results in a file. These user-initiated actions are separate from calculator processing. Upload and persistence behavior has not been verified here, so this guidance does not establish that equipment details are never uploaded or stored.